HAND PIECES

Hammer

Hand piece has a reciprocating rather than rotary action and its used at low speed (0-5,000 rpm) by jewelers for stone setting and decorative work. It requires periodic lubrication.

The Hammer  has a 1/32" stroke and its impact force an be adjusted from light to heavy  by turning the silver knurled adjusting ring. It comes with an Anvil  Point (10177) and pin for installing and tightening points. A Pave Point (R15PT) for special texturing and Styles with Carbide Tip (10212) for marking or scribing harden steel are available separately. 6-1/4" long, 1/4" Dia. at tip; Wt.3.65 ozs.; Shp. Wt. 4.85 ozs.

#15; Hammer Hand Piece; $133.00

#25

25C

Heavy Duty

Nos.25 and 25C are precision hand pieces made of continuous production work. Two models available- with collets (N0.25) or geared 3-jaw  #0  chuck (No.25C) Both have heavier duty housings  and double shielded ball bearings.

No. 25 Hand Piece comes with a 1/8" (3.18mm) and a 1/4 (6.35mm) collets and pin and chuck wrench. Other fractional and metric collets are available separately and in  Collet Set 103000 page 14 5-1/8 long, and 1-1/32" Dia.; Wt. 7.15 ozs.; Shp. Wt.9.6 ozs.

No. 25C comes with geared 3-jaw #0chuck with 0-5/32" (4mm) capacity and CK-O chuck key. 5-3/8" long, 1-32" Dia., Wt. 8.4 oz., Shp. Wt. 11.75 ozs.

#25; Hand Piece; $150.00

#25C; Hand Piece; $165.oo

Speed Increasing

Unique hand  piece with a ball bearing speed increase that produces 2.5 times the speed of the motor. This feature makes perfect for bright cutting with diamond flywheels and other high speed work with carbide and diamond points.

No.35hand piece comes with a 1/8" (3.18mm) collet installed unless otherwise specified. Other fractional  and metric collets are available separately and in Collet Set 103000 .PAGE 14 5-1/8" long, 1-3/32" Dia.., Wt. 7.15 ozs.; Shp. Wt. 9.6 ozs.

No. 25C comes with geared 3-jaw #0 chuck with 0-5/32" (4mm) capacity and CK-O chuck key. 5-1/8" long, 1-1/32" Dia., Wt.  8,4 ozs. Shp. Wt, 11.75 ozs.

#35; Hand Piece; $179.00

Angle Head for Latch-Type Accessories

No.55A 18"contra-anglehand piece is good for intricate and delicate jobs in awkward and hard--to-reach spots. 6-1/2" long, 7/16" Dia., max head dimension  5/8", Wt.2.1 ozs. Shp. Wt.3.5 ozs.

#55A; Hand Piece; $89.00

---------------------------------------

No. 56A is similar to 55A except that it has a right-angle head. 6-1/2" long, 7/16" Dia., max head dimension 5/8", Wt. 2..35 ozs., Shp. Wt.3.7 ozs.

Angle head hand pieces are for light and intermittent work and the miniature gears in their heads require frequent lubrication. They come with two latch-type mandrels. Can also be used with latch-type steel burs, mounted abrasive points, and diamond points available from Foredom- (see accessory pages.)

Use for a Wide Variety of Light-Duty Jobs in Hard-t0 Reach Places

• Deburring- Finishing and polishing of metals.

• Removing oxidation & cleaning of electrical and electronic contacts.

• Removing  flux coatings from PC Boards

• Reworking and repairing circuit boards.