Compared to flex shafts, micro motors have much less torque, however, the higher speed results in a comparable rate of material removal with a lighter touch.

The simple coil cord connection between the hand piece motor and control box is another key advantage. Unlike the "drag" and general restriction in maneuverability you have with a shaft and sheath, micro motors offer much greater freedom of movement.

1070 MICRO MOTOR KIT INCLUDES

Prices below are for individual components when purchased separately.

HP-917; CONTROL; $190.00

MH-170; HAND PIECE with 3/32" (2.35mm) COLLET; $210.00

HP4-960; VARIABLE SPEED FOOT CONTROL; $60.00

HP4-933; HAND PIECE CRADLE; $6.00

Spare pair of Motor Brushes, Spare Fuse, Collet changing Wrenches.

The complete Control has switches on the front for On/Off Power. Forward or Reverse Rotation, and Manual or Foot Speed Control. Speed can be adjusted from low to full speed using the dial on the box, or with the foot pedal. An Overload Protector Light is also featured that turns red and sounds a beeping alarm when motor stalls.

The back of the control box has a convenient voltage selector switch for operating with either 115 or 230 volt-no need to specify 230 volt when ordering. The control converts AC current to DC current required for the hand piece. The box also has receptacles for the Variable Speed Foot Control Hand Piece and an Optional On/Off Foot Switch (see below).

Bur changes are quick and easy with a simple twist of the front section of the Hand Piece, A Cradle is also supplied for the hand piece when not in use. A selection of collet adapters is available for simplifying changes between accessories with different shank sizes.

HP4-927;OPTIONAL ON/OFF FOOT SWITCH; $25.00

This control is available separately and does not come in the kit. It plugs into the back of the control box and allows you to turn the motor on and off without changing the speed set by the dial.

MH-170; HIGH SPEED ROTARY HAND PIECE; $210.00

6.2"overall length,5/8"grip diameter, 1" motor diameter, 7.3 ozs./208gr. DC30V/1.2a. CE marked.

It has a slender contoured grip for precise and very high speed work and quick release rotary type chuck. Use with accessories rated at least 45,000 RPM. Fan cooled, brush type continuous duty motor runs cool and vibration-free and permanently lubricated, shielded ball bearings require no lubrication. This hand piece can also be used with the FM3545 control.

Comes with 3/32" (2.35mm) collet that is easy to install and changes with supplied collet changing wrench. Optional 1/8" and 3mm collets are available. (see below)

REPLACEMENT COLLETS AND MOTOR BRUSHES FOR MH-170

HP4-117; 3/32" (2.35mm) COLLET (st'd size); $26.00

HP4-117B; 1/8" (3.18mm) COLLET; $26.00

HP4-117C; 3mm COLLET; $26.00

HP4-163; MOTOR BRUSHES FOR MH-170; $16.00

ADAPTOR COLLETS

Use collet adapter with different shank size accessories without having to change collets.

HPL4-3233; 3/32"to 1/16"; $15.00

HPL4-3234; 1/8" to 1/16"; $15.00

HPL4-3235; 3mm to 3/32"; $15.00

HPL4-3236; 1/8" to 3/32"; $15.00

PL4-3237; 3.0mm to 1.6mm: $15.00

Replacement collets and motor brushes for discontinued MH-145, MH-145A and MH-135 micro motor hand pieces.

HP813517; 1/8" (3.18mm) COLLET MH145A; $29.50

HP813516; 3/32" (2.35mm) COLLET; $29.50

HP813518; 3mm COLLET; $29.50

HPL4-504; MOTOR BRUSHES FOR MH-145A (Pair); $19.50

HPL4-304; MOTOR BRUSHES FOR MH-145 (Pair); $19.50

HPL813514; MOTOR BRUSHES FOR MH-135 (Pair); $19.50